top of page
Hardwire PDM 28
  • Hardwire PDM 28

    AU$3,350.00Price

    PDM 25

    A PDM (Power Distribution Module) is a device used to replace conventional relays and fuses in a vehicle electrical system. The Hardwire Electronics PDM takes inputs from physical switches, analogue voltages, or the CAN bus, and provides power to different electronic devices such as radiator fans, fuel pumps and head lights. The current being drawn from each connected device is continuously monitored. If the measured current is too high due to a fault, the PDM switches off the respective output to prevent further damage to the wiring loom or the connected device. The PDM can then retry the output to see if the fault has cleared.

    Approx 3 Weeks Lead Time
    SKU: HWPDM28
    • Tech Specs

      General

       

      Size

      318x124x58 mm

      Weight

      1640g

      Operating Temperature

      -55 – 90C  [ -67 – 194 °F ]

      Construction

      Machined Aluminium Enclosure, Media Blasted and Anodised Black

      IP Rating

      IP67 Water and Dust Ingress Protection

      Connectors

      2x 12-Pin DTM, 2x 12-Pin DT, 1x 4-Pin DTP

      Indicator LEDs

      50x RGB LEDs

      Inputs

       

      Type

      16 analogue inputs which can also serve as digital inputs.

      Measurement Range

      Each input can measure voltages between 0-28V, independent of the battery voltage.

      Measurement resolution

      16-bit or 0.001V

      Frequency Measurement

      Automatic frequency measurement up to 300Hz

      Protection

      Fully protected for input voltages between  -24V to 40V.

      Pull Up/Down Resistors

      Each input has a software selectable 10K Pull-up or Pull-down resistor

      Added Features

      Configure as active high or low. Configurable Hysteresis voltage. Latching or momentary operation.

      Outputs

       

      Type

      4 high/low side outputs 100A peak, 30A continuous, with reverse current protection.

      6 high/low side outputs 80A peak, 20A continuous, with reverse current protection.

      18 high/low side outputs 80A peak, 20A continuous

      Combined

      200A combined output maximum current

      Output current control steps

      100mA

      Protection

      Each output is overcurrent, overtemperature, load dump and reverse polarity protected.

      Soft Start

      PWM soft start can be enabled on outputs to limit inrush current.

      PWM

      Each output can be Pulse Width Modulated based on a user defined variable. This can limit the speed of radiator fans, fuel pumps, and dim lights.

      1000Hz maximum PWM frequency

      Added Features

      Outputs can be configured to stay on for a specified time after the input is removed, useful for thermo-fans.

      Outputs can be retried multiple times after an over-current event is detected.

       

       
      LIN Bus

      1x LIN Bus Port. Currently unsupported, enabled in future software update

      CAN Bus

       

      Interface

      3x CAN2.0A/B ports  (Bus 3 reserved for NIO Power Module Expansion)

      Bus Speed

      50, 100, 125, 250, 500, 1000 kbps

      Termination Resistor

      Both CAN bus ports have software selectable CAN termination resistors.

      Input Stream

      100x inputs, fully customisable variable parsing with bit masking, math functions, and compound CAN message filtering

      Output Stream

      100x Outputs, Fully customisable CAN frame construction with math functions

      CAN Keypad

       
       

      Support for Blink Marine, Grayhill, Motec, Haltech and Marlin CAN keypads.

      Up to four keypads can be used at once.

      Logging

       

      Storage

      128Mb of onboard flash storage for logging PDM data

      Speed

      1Hz to 50Hz

      Viewing

      Data can be downloaded and graphed via the Hardwire Electronics PDM configurator software or exported as a .CSV file and graphed in external software

      Functions

       

      Output Functions

      Each Output can be switched with a user defined function.

      Logical operators

      AND, OR, NOR, XOR, NAND, NOR, >, >=, <, <=, Equal, Not Equal.

      Maths Channels

       
       

      Fully customisable Maths Functions

      Mathematical Operators

      Mathematical Operators - Addition, Subtraction, Multiplication, Division, Modulus, Choose, Min, Max

      Binary Operators

      Binary Operators - AND, OR, XOR, Left Shift, Right Shift

      Counters

       
       

      Configurable counters which increment, decrement, and reset based on user defined conditions

      IMU

       

      Rotation

      3-axis rotational position measurement 0.1° resolution

      Gyroscope

      2000°/s 3-axis measurement

      Accelerometer

      -8g to 8g 3-axis measurement

      PCB temperature

      6-Zone PCB temperature measurement. 

      RTC

       
       

      Real Time Clock with battery backup for 30 days. Used to store the correct time and date for data logs. 

      USB

       

      Type

      USB 2.0 compliant with Mini-B

      Driver

      Integrated driver with Windows 10

      PC App

       

      Name

      Hardwire Electronics PDM configurator software.

      Compatibility

      Windows 10 machines

      Connectivity

      Easy connection to the PDM with USB and windows integrated drivers. No unreliable USB-serial converter needed.

    • Product Details

      • Included

        • PDM28
        • 2x DTM Connectors + Contacts
        • 2x DT Connectors + Contacts
        • 1x DTP Connector + Contacts
        • 2x Radlok Connectors
        • USB Flash Drive with Pro PDM Configurator Software and Instruction preloaded
        • 2m USB Cable
        • Printed A4 instruction manual.

       

    bottom of page